Company about
Home > Samsung Monitor > Samsung Monitor Not Working Properly

Samsung Monitor Not Working Properly

Contents

In elderly systems, another possible cause is that some hardware DVD decoder cards "steal" one color (usually magenta) and use it to map the DVD video signal onto the standard video You have been warned. it will not anymore function.. Most PCs can use graphics from the video card or the motherboard, but not both at the same time. have a peek here

Solutions: use monitor's on-screen-display to manually select analog or digital Some blank screen problems can happen when the video card outputs analog video data when using a digital cable or when Before adjusting "fit to screen" option on my monitor settings, the screen overscans and it looks like low tier quality. For further troubleshooting steps, see HP support document, Flat Panel Monitor Displays Message about No Signal, Signal out of Range, Sleep, or Power Save. Manufacturers set a threshold number below which they consider a display acceptable.

Samsung Monitor Troubleshooting Check Signal Cable

Check the manual to determine the optimum refresh rate for your LCD, and set your video adapter to use that rate. The video BIOS is responsible for making that work. Restart the computer. Sorry, there was a problem flagging this post.

For example, a 17" LCD operating in analog mode may support 60 Hz and 75 Hz refresh. If the system displays a VGA image properly, change your display settings to something supported by the CRT. Image wavers or shimmers periodically or constantly¶ This is usually caused by RF interference from another electrical or electronic device, particularly one that contains a motor. Samsung Monitor Not Turning On More about Displays 6 Comments Add Comment How do you reset the refresh rate on a momitor?

Finally, note that some models of video adapter simply don't function well with some models of LCD. Cancel wendyrose Rep: 1 Posted: 06/14/2014 Options Permalink History Hi friend, Yes you can,use the 9h super hardness otao tempered glass screen protector. Many video cards and monitors support higher screen refresh rates in analog mode than they can support in single link digital mode. Use reduced blanking - This reduces the pixel clock which may fix the corruption.

I held down the "talk" button for about ten seconds and touched the screen and it has worked for the past few days without a problem. Samsung Monitor Check Signal Cable Analog I'll go buy a damn video card I guess. Samsung worked with CNET to create a forum where people can ask questions and talk about all Samsung products and get help with everything from HDTVs, Smart TVs, home theater components, To correct this problem, connect the CRT to a different circuit or to a UPS or power conditioner that supplies standard voltage regardless of input voltage.

Samsung Monitor Display Problem

Verify that the CRT is plugged in (and that the receptacle has power), the video cable is connected to the video card, the computer and CRT are turned on, and the http://www.playtool.com/pages/dvitrouble/dvitrouble.html When I press the screen it comes back normal and when I relieve the pressure it goes black again. Samsung Monitor Troubleshooting Check Signal Cable I am extremely frustrated and no one seems to know what to do. Samsung Monitor Blank Screen The screen is very unstable¶ First, try setting the optimal refresh rate as described above.

Was this answer helpful? navigate here Using an analog cable (DVI-A or a VGA cable) may force the monitor to return the analog EDID if you want to run in analog mode. I see some of the smarter people here have posted some suggestions I wish I had been able to try way back when.You really should at least - download and install Turn on the display. Samsung Monitor Switching Between Analog And Hdmi

Then fill out a Samsung service request online (see Resources for link).After you have filled out the form, Samsung will email you a free pre-paid shipping label. If the power light comes on, the display has power, skip to Listen to the computer and look at the lights. In theory it should never happen. http://johnfladung.net/samsung-monitor/samsung-monitor-not-working.html CRT snaps, crackles, or pops when powered up, or emits a strong electrical odor¶ Catastrophic CRT failure is imminent.

When running in digital mode, the quality of the digital signals in the cable also get worse as the cable lengthens but the the image quality stays perfect until it hits Samsung Monitor Analog Digital Problem Do not remove the video port cover If your computer came with a graphics card, HP may have installed a plastic cover over the video port attached to the motherboard. If you must repair a CRT, take it to someone who knows what she is doing.

Cancel Most Helpful Answer Ti Man Rep: 127 3 1 Posted: 09/23/2011 Options Permalink History Sorry this is late in coming but to fix the frozen screen try using your finger

very satisfied Satisfied Somewhat Satisfied Dissatisfied very dissatisfied Q3. Then i can turn it on and charge it. The pc worked fine on another monitor (before this, haven't checked with one after). Samsung Monitor Check Signal Cable Hdmi http://www.youtube.com/watch?v=pOH-Fl3jl...

If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). FWIW, I've seen this problem on older Samsung panels but never on the Sony or NEC/LaCie panels I use. Another cabling problem you can have is if Windows is set up to use a screen mode which requires dual link but you are using a single link cable. http://johnfladung.net/samsung-monitor/samsung-monitor-dvi-not-working.html But they did offer me another $300 piece of @!$* from Samsung!

Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Someone please help. Samsung offers a 3-year warranty on all monitors. And yet, sometimes you get a blank screen running in DVI digital mode when powering up.

In that case, you can sometimes fix the problem by using a separate degaussing coil, available at RadioShack and similar stores for a few dollars. wants to pay $300 for a phone that works for 13months? it stopped working and as i touch the menu... When the screen goes gray and the Windows Shutdown dialog appears, leave that dialog onscreen, but ignore it.

There has to be some fix around... Do not press too hard. If you have a monitor which can display in both digital and analog mode, then it may have a VGA connector for analog mode and a DVI-D connector for digital mode. Change the display resolution You cannot do this if you cannot view the first startup screen.

Write down each cable location so you can reconnect them in the future. This is a dodge rather than a solution but it will allow you to keep using the computer while you try to figure out the problem. If you can hear the computer's fan spin and see lights on the computer, the problem is probably caused by the video cable connection or the display. If the display does not work on another computer, the display might be defective.

Turn the monitor on after Windows boots - Sometimes the BIOS and powerup screens display properly because the video BIOS correctly chooses between analog and digital and then Windows chooses incorrectly. Try the monitor on another computer and see if it works. hdd? The EDID data in the monitor tells the display driver which screen modes it can support so this should never happen.